| Castrol Optigear Synthetic X220/32/460/680 详细说明 （浏览225次） |
Castrol Optigear Synthetic X
Synthetic gear oils
Description
Castrol OptigearTM Synthetic X is based on synthetic hydrocarbons and a special plastic deformation (PD)
and surface improvement additive package.
The additive package, when activated by high specific loads and corresponding temperatures, helps to
e surface roughness without creating abrasion leading to the surface improvement (plastic
deformation.)
Optigear Synthetic X is a CLP-HC gear oil (according to DIN 51502) and exceeds the minimum
re according to DIN 51517, part 3, CLP gear oils.
Application
Optigear Synthetic X may be used in spur gear, bevel gears or planetary gear units and in heavy loaded
gear units, e.g. wind turbine main gears. It is also suitable for the lubrication of oil-lubricated rolling
bearings.
Depending on the specific application, Optigear Synthetic X may be used in an operating temperature
range from -30 °C to +95 °C.
Advantages
· High load carrying capacity
· Superior micro pitting protection
· Excellent friction reduction
· Good filtration properties
· Excellent bearing lubrication suitabilityCastrol Optigear Synthetic X
18/11/2005, Global Version Number 1
Castrol, Optigear and the Castrol logo are trademarks of Castrol Limited, used under licence.
All reasonable care has been taken to ensure that the information contained in this publication is accurate as of the date of printing. However, such
information may, nevertheless, be affected by changes in the blend formulation occurring subsequent to the date of printing. Material Safety Data Sheets are
available for all Castrol Ltd products. The MSDS must be consulted for appropriate information regarding storage, safe handling and disposal of a product.
Castrol (UK) Ltd, Industrial Lubricants & Services
Wakefield House, Aspect Park, Pipers Way, Swindon, Wiltshire SN3 1RE, UK
Tel.: +44 (0)845 964 51 11, Fax: +44 (0)1793 486 083
www.castrol.com/industrial
Typical Characteristics
Test Method Units X 150 X 220 X 320 X 460
ISO Viscosity Grade ASTM D 2422 - 150 220 320 460
Density at + 15°C ISO 12185 /
ASTM D4052 g/ml 0.847 0.850 0.854 0.856
Kinematic Viscosity
@ 40°C mm2
/s 146 218 325 459
@ 100°C
ISO 3104 /
ASTM D445 mm2
/s 19.0 25.9 34.9 45.0
Viscosity Index ISO 2909 /
ASTM 2270 148 151 152 153
Flash Point, COC ISO 2592 /
ASTM D92 °C > 250
Pour Point ISO 3016 /
ASTM D97 °C -39 -33 -33 -27
Rust Test
Procedure A (24 hrs Distilled
Water) Pass Pass Pass Pass
Procedure B (24 hrs Synthetic
Sea Water)
ISO 7210 /
ASTM D665
Pass Pass Pass Pass
Copper Corrosion (3 hrs @
100°C)
ISO 2160 /
ASTM D130 1a 1a 1a 1a
FE8 wear test (81212MPB-
7.5/80-80)
Roller wear
Cage wear
DIN 51819-3 mg
mg
<10
<10
FZG test
A/8.3/90 scoring load stage
A/16.6/90 scoring load stage
DIN 51354 >12
12
FZG micropitting test FVA No. 54 >10
Foam Sequence I
ISO 6247 /
ASTM D892 mls <100/10
Ageing behavior, Increase of
viscosity at 100°C after 1000
h
ASTM D 2893 % 2
Subject to usual manufacturing tolerances.
Additional Information
Optigear Synthetic X gear oil can be applied by an oil can, oil cup reservoir, splash, spray mist or by
automatic dispensing e and central or circulation systems.
It is compatible with mineral oils and esters. This means that traces up to 3% of previous oil in the gear
case after draining will not pose any problems. However, the beneficial effects of the special PD additives
are reduced when mixed with other gear oils. |
|
